Invacare HomeFill Oxygen Compressor is designed to supply pressurized oxygen to fill Invacare proprietary gas cylinders for ambulatory use while the patient receives therapeutic oxygen from an accessory oxygen concentrator. It can fill cylinders for portable use by ambulatory patients.

Benefits of HomeFill Oxygen Compressor

• Provides an unlimited, refillable oxygen supply 
• Ensures oxygen purity is always greater than 90% 
• Breathe from continuous flow oxygen concentrator at night 
• Multiple cylinder sizes are available

Invacare HomeFill Oxygen Compressor Features

• Patient breathes from a continuous flow oxygen concentrator at night
• Patient protection ensures oxygen purity in cylinder is always greater than 90% 
• No extra equipment needed because patients can breathe off concentrator while filling cylinders
• Provides an unlimited refillable ambulatory oxygen supply
• Encourages compliance with oxygen therapy as patients have no worries about running out of oxygen
• System is compatible with 5 liter or 10 liter concentrators and a wide variety of cylinder options (Concentrators and cylinders are not included)
• Eliminating oxygen deliveries increases independence, convenience and comfort
• Allows the patient to breathe at home from a continuous flow concentrator and then use a convenient ambulatory pack when they are “out and about.”

What does HomeFill Compressor Include?

• Multistage compressor
• Internal reservoir
• Inlet fitting
• Control electronics with an integral oxygen concentration sensor
• Interlocking fill fitting
• Drive motor

What to buy with Invacare Oxygen Compressor

• Invacare HomeFill CGA870 Post Valve Cylinders (Code HF2POST9)
• Invacare HomeFill Continuous Flow D Cylinder (Code IOH2M6)
• Invacare HomeFill Ambulatory Package (Code IOH200PC)

Homefill Oxygen Tanks Cylinder Parts
  

How to fill Invacare Homefill Tanks?

https://www.youtube.com/watch?v=i3qk9-mZQuU
Video on How to Use the HomeFill Oxygen Compressor

How to use Oxygen Concentrator?

Connecting the Cylinder to the Compressor

1. Examine the cylinder gauge. If the cylinder pressure is less than 1500 psig, proceed to Step 2.
2. Set the regulator flow dial on the cylinder to Off
3. Remove the cylinder and connector fillport covers (if present)
4. Momentarily push Down on the outer ring (sleeve) of the connector fillport until Green dots are visible to reset the connector
5. Grasp the cylinder in the area behind the cylinder fillport
6. Position the cylinder in the compressor cradle
7. Align the cylinder fillport with the connector fillport
8. Pull Up on the outer ring (sleeve) of the connector fillport while pushing Down on the cylinder to couple the cylinder fillport into the connector fillport

Disconnecting the Cylinder from the Compressor

1. Press the compressor power switch to the Off (O) position
2. Grasp the cylinder in the area behind the cylinder fillport
3. With the other hand, grasp the outer ring (sleeve) of the connector fillport and push Down F
4. Lift up on the cylinder to remove from the connector fillport
5. When the cylinder fillport is disconnected from the connector fillport, release the outer ring (sleeve) of the connector fillport and use two hands to remove the cylinder from the compressor cradle
6. Place the fillport covers onto the connector fillport and cylinder fillport
7. Examine the cylinder gauge to ensure cylinder is full (needle pointing into Green area). If the cylinder is not full, perform the following:
   
   • Repeat Connecting the Cylinder to the Compressor
   • If cylinder is not full after second attempt to fill, contact the provider.

Turning the Compressor On and Off

1. Make sure the concentrator is On
2. Set the concentrator flow rate to the patient to 3 L/min or less for Platinum 5, XL, and Perfecto2 and 5 L/min or less for Platinum
3. Make sure the cylinder is connected to the compressor
4. Push the power switch on the control panel to the On ( I ) position
5. Examine the control panel. The following sequence of events should occur:
   
   • 0-3 minutes - The O2 Below Normal (YELLOW) light will be lit while the compressor warms up
   • After three minutes - The Filling (GREEN) light will be on while the cylinder is filling
   • The Full (GREEN) light will be on when the cylinder is finished filling
6. Remove the full cylinder
7. Push the power switch to the Off (O) position

Size Diagram